- 1 How do you finish marble tile edges?
- 2 Can you grind down marble tile?
- 3 How do you hide the edges of tile?
- 4 How do you finish tile edges with caulking?
- 5 Can you put tile trim on after tiling?
- 6 Can I sand tile edges?
- 7 What is bullnose tile trim?
- 8 How do you polish and seal marble?
- 9 How do you finish slate tile edges?
- 10 Can you grind down uneven tiles?
- 11 Can you use an orbital sander to polish marble?
- 12 Can I grind marble?
How do you finish marble tile edges?
Change to a 400-grit diamond disk to begin polishing the edge of the marble. You should notice a slight shine to the edge after using this disk. Switch to an 800-grit disk for a couple of passes, then move to a 1,500-grit disk. These create a bright, polished shine on the edge of the marble.
Can you grind down marble tile?
Both polishing compounds and diamond abrasive disks will successfully grind marble down, removing scratches and restoring the original polish and shine. If marble has uneven tiles, deep cracks or holes, or hairline fractures, you should have a professional examine the marble.
How do you hide the edges of tile?
You could use an angle grinder to clean up the edge a bit, then nail wood 1/4 round trim along there. Use paintable caulk to hide the seam, then paint with high gloss to match (or complement/contrast) the tile.
How do you finish tile edges with caulking?
Caulk the Edge To give the edge a clean, water-tight finish, place a piece of masking tape one grout joint away from the edge of the last tile. Fill this gap between the tile and the masking tape with a smooth bead of caulk. This will finish the edge without extra tiles.
Can you put tile trim on after tiling?
Use a hoover to suck out the loose adhesive before checking that your trim will sit flush all the way along the tiles, repeat the cutting if necessary. Spread fresh tile adhesive all along the cleaned up edge and push the trim in. Clean all excess adhesive and re-grout if needed.
Can I sand tile edges?
In a pinch, any concrete slab or cement block can be used to sand down the rough edge of a ceramic tile. You will need to hold the tile itself and slide it back and forth across the slab or block. However, it is an effective way to remove the sharp and potentially dangerous edge from any ceramic tile.
What is bullnose tile trim?
Bullnose tile is recognizable because of its characteristic rounded edges. It’s viewed as an edge treatment or trim piece, and is often used to cover corners or frame the perimeter of a tile design. This eliminates sharper angles and unfinished tile sides from being visible on your floor or wall.
How do you polish and seal marble?
Dry the marble top with a chamois cloth. Buff, it to shine by rubbing the entire surface with the cloth in small circles. Cover the surface with commercial stone polish or marble-polishing paste if you want more shine after buffing with a chamois. If using a spray-on stone polish, wipe with a soft rag.
How do you finish slate tile edges?
Gently grind the slate edges with a hand- held grinder. Bevel the top edge at a 45-degree angle, or a rounded edge or no angle at all, depending on your preference. Keep the grinder moving in slow arcs. Grind until the shape is as desired.
Can you grind down uneven tiles?
Grind Them Grinding is typically recommended when the floor cannot be removed. The floors are ground down with a floor or angle grinder fitted with a 50-grit disc, followed by a 100-grit, 200-grit and finally 400-grit discs.
Can you use an orbital sander to polish marble?
You need a machine. I used an orbital sander and it worked like a dream. I made the marble was wet all the time with just a sponge. You might see scratches if you don’t wet the marble and don’t skip any pads.
Can I grind marble?
Grind It Out Marble grinding can eliminate wear patterns, chips, cracks, stains, and other major marble issues. The experts at Love Marble can apply marble grinding to restore the original luster and appeal of marble flooring and other surfaces so they look better than brand new.